產品搜索
使用直流高壓發生器前應查看其完好性，聯接電纜線不該有斷路和短路，設備無決裂等損壞，將機箱、倍壓筒放置到適宜的安全的方位，別離聯接好電源線、電纜線和接地線，維護接地線與作業接地線以及放電棒的接地線均應獨自接到試品的地線上并保證接地，禁止各接地線彼此串聯運用，防止擊穿時地電位舉高構成反擊，損壞儀器。
首先查看電源開關是否在關斷的方位上，并查看調壓電位器應在零位上，過電壓維護整定撥盤開關設置在恰當的方位上，一般為1.10~1.20倍測驗電壓值，直流高壓發生器空載升壓驗證過電壓維護整定值，請認準電源是單相溝通220V，50Hz接通電源開關，此刻綠燈亮，表明電源接通，按赤色按鈕，則紅燈亮，表明高壓接通。
順時針方向陡峭調理調壓電位器，輸出端即從零開端升壓，電壓表顯現為負載試品上的電壓值，電流表則顯現試品上流過的電流與一切走漏電流之和，電流以微安為單位，升到所需的電壓后，按規則時刻記載電流表讀數，并查看控制箱及輸出電纜有無異常現象及動靜，降壓，將調壓電位器回零后，隨后按綠色按鈕，堵截高壓并封閉電源開關。
我們在做負載實驗前，將高壓屏蔽微安表安裝到倍壓筒上的高壓輸出端上，并將配套的專用高壓線別離接到微安表上和被試品上，查看直流高壓發生器、放電棒、倍壓筒、試品聯接線、接地線是否正確，接地線聯接是否牢靠，查看高壓安全間隔是否符合要求，方可開端進行試品的高壓實驗。
查看儀器等無異常情況后，接通單相溝通220V電源開關，此刻綠燈亮，表明電源接通，可開端進行試品的直流走漏和直流耐壓實驗，按赤色按鈕，則紅燈亮，表明高壓接通，待升高壓，順時針方向陡峭調理調壓電位器，輸出端即從零開端升壓，升壓速度以每秒3-5kV上升實驗電壓為宜。
因此大家在使用直流高壓發生器之前，需要熟讀說明書，嚴格按照說明書來進行操作。
